Les résolutions d’images vidéo analogique et numérique

Texte original par David Gouvenel
Janvier 2019


PIXEL RVB FORMANT L’IMAGE

Résolution des Standards Informatiques

SigleNomRésolution x DéfinitionFormatFréquence
Verticale
CGA 320 x 2001.5mini 60 Hz
EGA 640 x 3501.8mini 60 Hz
VGA(Video Graphic Array)640 x 4804/3=1.33mini 60 Hz
S-VGA(Super-VGA)800 x 6004/3=1.33mini 60 Hz
XGA (eXtra Graphic Array)1024 x 7684/3=1.33mini 60 Hz
WXGA (Wide eXtra Graphic Array)1366 x 7681.77(16/9)mini 60 Hz
 XGA+(eXtra Graphic Array+) 1152 x 8641.5mini 60 Hz
 WXGA+(Wide eXtra Graphic Array+) 1440 x 9001.6 (16/10)mini 60 Hz
S-XGA(Super-XGA)1280 x 1024 1.25mini 60 Hz
HD(HD 720)1280 x 72016/9mini 60 Hz
WS-XGA(Wide Super-XGA)1600 x 1024 1.56 (25/16)mini 60 Hz
S-XGA+(Super-XGA+)1400 x 10501.25mini 60 Hz
WS-XGA+(Wide Super-XGA+)1680 x 10501.6 (16/10)mini 60 Hz
U-XGA(Ultra-XGA)1600 x 12001.33mini 60 Hz
FHD 1080(Full-HD 1080) 1920 x 108016/9mini 60 Hz
WU-XGA (Wide  U-XGA)1920 x 12001.6 (16/10)mini 60 Hz
QHD(Quad-HD)2560 x 144016/9mini 60 Hz
Q-XGA(Quad-XGA)2048 x 15361.33mini 60 Hz
WQ-XGA(Wide Quad-XGA)2560 x 16001.6 (16/10)mini 60 Hz
4K UHD(4k – Ultra-HD)3840 x 216016/9mini 60 Hz

Résolutions des Standards Vidéo

Sigle Nom Résolution x Définition
(image)
Format Fréquence
Verticale
 
SECAM (SEquentiel Couleur A Mémoire)
( image 25 Hz / trame 50 Hz )
384 x 576 1.33 50 Hz  
PAL (Phase Alternative Line)
( image 25 Hz / trame 50 Hz )
450 x 576 1.33 50 Hz  
NTSC (National Television System Comittee)
(image 30 Hz / trame 60 Hz )
323 x 486 1.33 60 Hz  
MPEG – 1 (Motion Picture Expert Group norme 1)
PAL ( image 25 Hz / trame 50 Hz )
352 x 288 1.33 50 Hz  
MPEG – 1 (Motion Picture Expert Group norme 1)
NTSC (image 30 Hz / trame 60 Hz )
352 x 243 1.33 60 Hz  
MPEG – 2 SD PAL (Motion Picture Expert Group norme 2)
PAL ( image 25 Hz / trame 50 Hz )

720 x 576
1.33 (pixel rectangulaire 1.06) ou 16/9 (pixel rectangulaire 1.42) 50 Hz SD
CREATION 1994
MPEG – 2 SD NTSC (Motion Picture Expert Group norme 2)
NTSC (image 30 Hz / trame 60 Hz )
720 x 480 1.33 (pixel rectangulaire 0.88) ou 16/9 (pixel rectangulaire 1.18) 60 Hz SD
CREATION 1994
MPEG – 2 HD(Motion Picture Expert Group norme 2) 720p1280 x 72016/950 Hz / 60 HzHD
CREATION 2000
MPEG – 2 HD(Motion Picture Expert Group norme 2) 1080i1920 x 108016/950 Hz / 60 HzFULL-HD (2K)
CREATION 2006
MPEG – 4 SD NTSC(Motion Picture Expert Group norme 4) 720 x 48016/9 (pixel rectangulaire 1.18) 60 Hz SD
CREATION 1994
MPEG – 4 SD PAL(Motion Picture Expert Group norme 4) 720 x 57616/9 (pixel rectangulaire 1.42) 50 Hz SD
CREATION 1994
MPEG – 4 HD(Motion Picture Expert Group norme 4) 720p 1280 x 72016/9 50 Hz / 60 Hz HD
CREATION 2000
MPEG – 4 HD(Motion Picture Expert Group norme 4) 1080i 1920 x 108016/9 50 Hz / 60 Hz FULL-HD (2K)
CREATION 2006
HEVC 3840 x 216016/9 50 Hz / 60 Hz ULTRA – HAUTE DEFINITION
ULTRA-HD (4K)
CREATION 2012
HEVC-2 7680 x 432016/9 50 Hz / 60 Hz ULTRA – HAUTE DEFINITION
ULTRA-HD (8K)
CREATION 2018
HD Ready


HD Ready 720p

Full HD


Full HD 1080p

Ultra HD


4K Ultra-HD 2160p

Ultra-HD


4K Ultra-HD 2160p et 8K Ultra-HD 4320p

4K HDR


4K ULTRA-HD HDR

8K HDR


8K ULTRA-HD HDR

Hisense H9


HISENSE H9 – TV LCD EDGE LED ULTRA-HD 4K 3D PASSIVE ANDROID SMART TV

L’ULTRA-HD 4K apporte 4 fois plus de pixels que le FULL-HD 2K

LE SD (NTSC) 720 x 480 = 345 600 pixels
LE SD (PAL) 720 x 576 = 414 720 pixels
LE HD READY 1K 1280 x 720 = 921 600 pixels
LE FULL-HD 2K 1920 x 1080 = 2 073 600 pixels
L’ULTRA HD 4K 3840 x 2160 = 8 294 400 pixels
L’ULTRA-HD 8K 7680 x 4320 = 33 177 600 pixels

Résolutions des Supports Vidéo

Sigle Codage Résolution x Définition
(image)
Format Fréquence
Verticale
 
DVD PAL MPEG 2 720 x 576 4/3 (pixel rectangulaire 1.06) ou 16/9 (pixel rectangulaire 1.42) 50 Hz SD
CREATION 1998
DVD NTSC MPEG 2 720 x 480 4/3 (pixel rectangulaire 0.88) ou 16/9 (pixel rectangulaire 1.18) 60 Hz SD
CREATION 1997
D1/DV PAL 720 x 5764/3 (pixel rectangulaire 1.06) 50 Hz SD
D1/DV PAL 720 x 57616/9 (pixel rectangulaire 1.42) 50 Hz SD
D1/DV NTSC 720 x 4804/3 (pixel rectangulaire 0.88) 60 Hz SD
D1/DV NTSC 720 x 48016/9 (pixel rectangulaire 1.18) 60 Hz SD
HDV 1440 x 108016/9 (pixel rectangulaire 1.33) 50 Hz FULL-HD (2K)
BLU-RAYH.264 1920 x 108016/9 (pixel carré) 50 Hz FULL-HD (2K)
CREATION 2003
BLU-RAY 4KH.2653840 x 216016/9 (pixel carré)50 HzULTRA-HD (4K)
CREATION 2015

High Efficiency Video Coding (HEVC) ou AVC/H.265 :
ce nouveau codage offre la qualité HD que l’on connaît, mais pour un débit deux fois moindre.
Ou une qualité Ultra HD pour le débit HD actuel. 

Résolutions du Cinéma Numérique 4K
Salle de cinéma

SigleRésolution x Définition
(image)
FormatNombre de Pixels
DCI 4K NATIVE 4096 x 21601.908 847 360
DCI 4 K CINEMASCOPE4096 x 17142.397 020 544
DCI 4 K PANAVISION3996 x 21601.858 631 360

Profondeur des couleurs :

Codage du pixel sur : Nombre de nuances de rouge,
de vert et de bleu :
Nombre de couleurs par pixel : Nom : Spectre visible
par l’oeil
humain
1+1+1=1 bits22MONOCHROME 
2+2+2=6 bits464CGA 
3+3+3=9 bits8512  
4+4+4=12 bits 16 4096 AMSTRAD CPC,
ATARI ST, EGA
 
5+5+5=15 bits3232768AMIGA 
5+6+5=16 bits 65 536High Color 
6+6+6=18 bits64262144AMIGA 
8+8+8=24 bits 256 16 777 216 True Color,VGA
Standard
Rec.709
35,9%
10+10+10=30 bits10241 073 741 824Rec.2020
HDR-10
75,8%
12+12+12=36 bits409668 719 476 000Rec.2020
HDR-12
Dolby Vision
> 100 %

Les diffuseurs d’image :

Les moniteurs 4/3

Diagonale du tube
en cm (en pouces)
Dimension image visible en 4/3
(largeur en cm x hauteur en cm)
Nombre de pixels
(Largeur x Hauteur)
format de l’écran
(largeur/hauteur)
Taille moyenne
du pixel
35 cm (14″) 26 x 20 800 x 600 1.33 0.30 mm
38 cm (15″) 29 x 22 1024 x 768 1.33 0.29 mm
43 cm (17″) 32 x 24 1200 x 900 1.33 0.27 mm
48 cm (19″) 36 x 27 1400 x 1050 1.33 0.26 mm
53 cm (21″) 40.8 x 30.6 1600 x 1200 1.33 0.26 mm

Les téléviseurs cathodiques, rétroprojecteurs à tubes 4/3 et 16/9


TELEVISEUR CATHODIQUE 16/9 LOEWE

Diagonale du tube
en cm (en pouces)
Dimension image visible en 4/3
et 16/9
(largeur en cm x hauteur en cm)
Nombre de pixels
(Largeur x Hauteur)
format de l’écran
(largeur/hauteur)
Taille moyenne
du pixel
35 cm (14″) 26 x 20 (26 x 15) 330 x 576 4/3 0.6 mm
53 cm (21″) 40.8 x 30.6 (40.8 x 23) 360 x 576 4/3 0.6 mm
63 cm (25″) 47.2 x 35.4 (47.2 x 26.6) 530 x 576 4/3 0.8 mm
73 cm (29″) 54.4 x 40.8 (54.4 x 30.7) 560 x 576 4/3 0.8 mm
82 cm (32″) 64 x 48 (64 x 36.2) 600 x 576 4/3 1.07 mm
90 cm (36″) 70 x 52 (70 x 39) 650 x 576 4/3 1.07 mm
103 cm (41″) 82.4 x 61.8 (82.4 x 46.5)   4/3  
117 cm (46″) 93.6 x 70.2 (93.6 x 52.9)   4/3  
135 cm (53″) 108 x 81 (108 x 61)   4/3  
70 cm (28″) 57 x 32 (42.7 x 32) 530 x 576 16/9 1.07 mm
80 cm (32″) 66.3 x 37.3 (49.7 x 37.3) 630 x 576 16/9 1.07 mm
90 cm (36″) 75 x 42.2 (56.3 x 42.2) 700 x 576 16/9 1.07 mm
102 cm (40″) 88.9 x 50 (88.9 x 50)   16/9  
127 cm (50″) 110.7 x 62.3 (110.7 x 62.3)   16/9  

Remarque : les plus grandes diagonales en tube cathodique (CRT) font 102 cm
à cause du poids et de l’encombrement du téléviseur.

Les téléviseurs LCD et Plasma 16/9 FULL-HD (2K) / ULTRA-HD (4K)

LG CINEMA 3D 4K


TELEVISEUR LCD FULL LED 84 POUCES LG 84LM960V CINEMA 3D PASSIVE 16/9 ULTRA HIGH DEFINITION TV
3840 x 2160 PIXELS (ULTRA-HD 4K) (15 000 EUROS)
LE PLUS GRAND ECRAN LED ULTRA-HD 2160p DU MONDE !

Diagonale de l’écran
en cm (en pouces)
Dimension image visible en 16/9
(largeur en cm x hauteur en cm)
Nombre de pixels
(Largeur x Hauteur)
format de l’écran
(largeur/hauteur)
Taille moyenne
du pixel
81 cm (32″) 71 cm x 40 cm 1920 x 1080 16/9 0.37 mm
94 cm (37″) 82 cm x 46 cm 1920 x 1080 16/9 0.43 mm
102 cm (40″) 89 cm x 50 cm 1920 x 1080 16/9 0.46 mm
102 cm (40″)89 cm x 50 cm3840 x 216016/90.23 mm
107 cm (42″)93 cm x 52 cm1920 x 108016/90.48 mm
107 cm (42″)93 cm x 52 cm3840 x 216016/90.24 mm
119 cm (47″) 103 cm x 58 cm 1920 x 1080 16/9 0.53 mm
124 cm (49″)108 cm x 61 cm3840 x 216016/90.28 mm
127 cm (50″) 111 cm x 62 cm 1920 x 1080 16/9 0.57 mm
132 cm (52″) 115 cm x 65 cm 1920 x 1080 16/9 0.59 mm
140 cm (55″) 122 cm x 69 cm 1920 x 1080 16/9 0.63 mm
140 cm (55″)122 cm x 69 cm3840 x 216016/90.32 mm
152 cm (60″) 132 cm x 75 cm 1920 x 1080 16/9 0.68 mm
165 cm (65″) 144 cm x 81 cm 1920 x 1080 16/9 0.75 mm
165 cm (65″)144 cm x 81 cm3840 x 216016/90.37 mm
165 cm (65″)144 cm x 81 cm7680 x 432016/90.18 mm
178 cm (70″) 154 cm x 87 cm 1920 x 1080 16/9 0.80 mm
190 cm (75″)165 cm x 93 cm3840 x 216016/90.43 mm
190 cm (75″)165 cm x 93 cm7680 x 432016/90.21 mm
195 cm (77″)169 cm x 95 cm3840 x 216016/90.44 mm
201 cm (79″)175 cm x 98 cm3840 x 216016/90.45 mm
208 cm (82″)181 cm x 102 cm3840 x 216016/90.47 mm
208 cm (82″)181 cm x 102 cm7680 x 432016/90.23 mm
213 cm (84″) 185 cm x 104 cm 1920 x 1080 16/9 0.96 mm
213 cm (84″) 185 cm x 104 cm 3840 x 2160 16/9 0.48 mm
213 cm (84″)185 cm x 104 cm7680 x 432016/90.24 mm
216 cm (85″)188 cm x 106 cm3840 x 216016/90.49 mm
216 cm (85″)188 cm x 106 cm7680 x 432016/90.24 mm
223 cm (88″)194 cm x 109 cm7680 x 432016/90.25mm
249 cm (98″)217 cm x 122 cm3840 x 216016/90.56 mm
249 cm (98″)217 cm x 122 cm7680 x 432016/90.28 mm
262 cm (103″) 227 cm x 128 cm 1920 x 1080 16/9 1.18 mm
370 cm (146″)318 cm x 179 cm3840 x 216016/90,83 mm
556 cm (219″)484 cm x 272 cm3840 x 216016/91,26 mm
ECRAN 16/9 233 CM   
267 cm (105″)233 cm x 131 cm1280 x 72016/91,82 mm
251cm (99″)233 cm x 99 cm1280 x 54421/91,82 mm
267 cm (105″)233 cm x 131 cm1920 x 108016/91,2 mm
251cm (99″)233 cm x 99 cm1920 x 81721/91,2 mm
267cm (105″)233 cm x 131 cm3840 x 216016/90,6 mm
251cm (99″)233 cm x 99 cm3840 x 163421/90,6 mm
ECRAN 21/9 270 CM   
292 cm (115″)270 cm x 115 cm1920 x 81721/91,4 mm
234 cm (92″)204 cm x 115 cm1920 x 108016/91,06 mm
ECRAN 16/9 270 CM   
307 cm (121″)270 cm x 151 cm1920 x 108016/91,4 mm
292 cm (115″)270 cm x 115 cm1920 x 81721/91,4 mm
307 cm (121″)270 cm x 151 cm3840 x 216016/90,7 mm
292 cm (115″)270 cm x 115 cm3840 x 163421/90,7 mm
ECRAN 21/9 280 CM   
305 cm (120″)280 cm x 119 cm1920 x 81721/91,4 mm
242 cm (95″)211 cm x 119 cm1920 x 108016/91,09 mm
ECRAN 16/9 318 CM   
370 cm (146″)318 cm x 179 cm3840 x 216016/90,828 mm
342 cm (135″)318 cm x 135 cm3840 x 163421/90,828 mm
HISENSE XT910


HISENSE XT910 65 POUCES (165 CM) 3840 x 2160 PIXELS (ULTRA-HD 4K) (2700 EUROS)
DALLE 10 BITS FULL LED LOCAL DIMMING 240 ZONES COMPATIBLE HDR-10, 3D ACTIVE

SONY ZD9


SONY 65ZD9 65 POUCES (165 CM) 3840 x 2160 PIXELS (ULTRA-HD 4K) (5000 EUROS)
DALLE 10 BITS FULL LED LOCAL DIMMING 600 ZONES PIC LUMINEUX 1800 NITS
COMPATIBLE HDR-10,HLG, DOLBY VISION, 3D ACTIVE

Distance de recul pour visionner un écran LCD : FULL-HD
ou ULTRA-HD
avec une source ULTRA-HD, FULL-HD ou SD

Le pouvoir de résolution de l’œil est d’environ une minute d’arc (60 secondes d’arc, 0,017°), soit environ 100 km sur la surface de la Lune vue de la Terre, ou plus proche de nous, un détail d’environ 1 mm pour un objet ou une image situé à 3 m de distance.

Le pouvoir séparateur de l’oeil humain est de e=1/3000 radians

soit 0,33 mm à 1 m de distance
soit 1 mm à 3 m de distance
soit 3,3 mm à 10 m de distance

Diagonale de l’écran
en cm (en pouces)
Dimension image visible en 16/9
(largeur en cm x hauteur en cm)
Nombre de pixels
(Largeur x Hauteur)
Distance de recul optimale Taille moyenne
du pixel
81 cm (32″)71 cm x 40 cm3840 x 2160 (ULTRA-HD 4K)0,56 m0.18 mm
81 cm (32″) 71 cm x 40 cm 1920 x 1080 (FHD) 1,12 m 0.37 mm
81 cm (32″)71 cm x 40 cm1366 x 768 1,58 m0.52 mm
81 cm (32″) 71 cm x 40 cm 720 x 576 (SD)2,10 m0.69 mm
94 cm (37″) 82 cm x 46 cm 1920 x 1080 (FHD) 1,30 m 0.43 mm
94 cm (37″) 82 cm x 46 cm 720 x 576 (SD) 2,42 m 0.80 mm
102 cm (40″)89 cm x 50 cm3840 x 2160 (ULTRA-HD 4K)0,69 m0.23 mm
102 cm (40″) 89 cm x 50 cm 1920 x 1080 (FHD) 1,40 m 0.46 mm
102 cm (40″) 89 cm x 50 cm 720 x 576 (SD) 2,63 m 0.87 mm
107 cm (42″)93 cm x 52 cm3840 x 2160 (ULTRA-HD 4K)0,73 m0.24 mm
107 cm (42″) 93 cm x 52 cm 1920 x 1080 (FHD) 1,45 m 0.48 mm
107 cm (42″) 93 cm x 52 cm720 x 576 (SD)2,73 m 0.90 mm
119 cm (47″) 103 cm x 58 cm 1920 x 1080 (FHD) 1,62 m 0.53 mm
119 cm (47″) 103 cm x 58 cm 720 x 576 (SD) 3,05 m 1 mm
124 cm (49″)108 cm x 61 cm3840 x 2160 (ULTRA-HD 4K)0,85 m0.28 mm
124 cm (49″)108 cm x 61 cm1920 x 1080 (FHD)1,69 m0.56 mm
124 cm (49″)108 cm x 61 cm720 x 576 (SD)3,21 m1.06 mm
127 cm (50″) 111 cm x 62 cm 1920 x 1080 (FHD) 1,73 m 0.57 mm
127 cm (50″) 111 cm x 62 cm 720 x 576 (SD) 3,26 m 1.08 mm
132 cm (52″) 115 cm x 65 cm 1920 x 1080 (HD) 1,82 m 0.60 mm
132 cm (52″) 115 cm x 65 cm 720 x 576 (SD) 3,42 m 1.13 mm
140 cm (55″)122 cm x 69 cm3840 x 2160 (ULTRA-HD 4K)0,97 m0.31 mm
140 cm (55″) 122 cm x 69 cm 1920 x 1080 (FHD) 1,94 m 0.64 mm
140 cm (55″) 122 cm x 69 cm 720 x 576 (SD) 3,63 m 1.20 mm
152 cm (60″) 132 cm x 75 cm 1920 x 1080 (FHD) 2,10 m 0.69 mm
152 cm (60″) 132 cm x 75 cm 720 x 576 (SD) 3,94 m 1.30 mm
165 cm (65″)144 cm x 81 cm7680 x 4320 (ULTRA-HD 8K)0,57 m0.18 mm
165 cm (65″)144 cm x 81 cm3840 x 2160 (ULTRA-HD 4K)1,13 m0.37 mm
165 cm (65″) 144 cm x 81 cm 1920 x 1080 (FHD) 2,27 m 0.75 mm
165 cm (65″) 144 cm x 81 cm 720 x 576 (SD) 4,26 m 1.40 mm
178 cm (70″) 154 cm x 87 cm 1920 x 1080 (FHD) 2,43 m 0.80 mm
178 cm (70″) 154 cm x 87 cm 720 x 576 (SD) 4,56 m 1.50 mm
190 cm (75″)165 cm x 93 cm7680 x 4320 (ULTRA-HD 8K)0,63 m0.21 mm
190 cm (75″)165 cm x 93 cm3840 x 2160 (ULTRA-HD 4K)1,30 m0.43 mm
190 cm (75″)165 cm x 93 cm1920 x 1080
(FULL-HD)
2,60 m0.86 mm
190 cm (75″)165 cm x 93 cm720 x 576 (SD)4,89 m1.61 mm
201 cm (79″)175 cm x 98 cm3840 x 2160 (ULTRA-HD 4K)1,36 m0.45 mm
201 cm (79″)175 cm x 98 cm1920 x 1080 (FHD)2,76 m0.91 mm
201 cm (79″)175 cm x 98 cm720 x 576 (SD)5,15 m1.70 mm
203 cm (80″) 177 cm x 100 cm 1920 x 1080 (FHD) 2,79 m 0.92 mm
203 cm (80″) 177 cm x 100 cm 720 x 576 (SD) 5,24 m 1.73 mm
213 cm (84″)185 cm x 104 cm7680 x 4320 (ULTRA-HD 8K)0,72 m0.24 mm
213 cm (84″)185 cm x 104 cm3840 x 2160 (ULTRA-HD 4K)1,45 m0.48 mm
213 cm (84″)185 cm x 104 cm1920 x 1080
(FULL-HD)
2,90 m0.96 mm
213 cm (84″) 185 cm x 104 cm 720 x 576 (SD) 5,48 m 1.80 mm
249 cm (98″)217 cm x 122 cm7680 x 4320 (ULTRA-HD 8K)0,84 m0.28 mm
249 cm (98″)217 cm x 122 cm3840 x 2160 (ULTRA-HD 4K)1,70 m0.56 mm
249 cm (98″)217 cm x 122 cm1920 x 1080
(FULL-HD)
2,90 m1.13 mm
249 cm (98″)217 cm x 122 cm720 x 576 (SD)5,48 m2.12 mm
262 cm (103″)227 cm x 128 cm3840 x 2160 (FHD)1,79m0,59 mm
262 cm (103″)227 cm x 128 cm1920 x 1080 (FHD)3,58m1.18 mm
262 cm (103″)227 cm x 128 cm720 x 576 (SD)6,72 m2.21 mm
SANYO PLZ4 HD READY 720P ECRAN 16/9  
ECRAN 233 CM DE BASE   
267 cm (105″)233 cm x 131 cm1280 x 720 (HD)5,50 m1,82 mm
251cm (99″)233 cm x 99 cm1280 x 544 (21/9)5,50 m1,82 mm
JVC DLA N5 ECRAN 16/9   
ECRAN 233 CM DE BASE   
267 cm (105″)233 cm x 131 cm1920 x 1080 (FHD)3,63 m1,2 mm
251cm (99″)233 cm x 99 cm1920 x 817 (21/9)3,63 m1,2 mm
267 cm (105″)233 cm x 131cm3840 x 2160 (ULTRA-HD 4K)1,80 m0,6 mm
251cm (99″)233 cm x 99 cm3840 x 1634 (21/9)1,80 m0,6 mm
JVC DLA N5 / SONY VPL-VW270ES ECRAN SCOPE 21/9  
ECRAN 270 CM DE BASE ECRAN SCOPE 21/9  
292 cm (115″)270 cm x 115 cm1920 x 817 (21/9)4,20 m1,4 mm
234 cm (92″)204 cm x 115 cm1920 x 1080 (16/9)3,18 m1,06 mm
292 cm (115″)270 cm x 115 cm3840 x 1634 (21/9)2,11 m0,7 mm
234 cm (92″)204 cm x 115 cm3840 x 2160 (16/9)1,59 m0,53 mm
ECRAN 270 CM DE BASE 16/9   
308 cm (121″)270 cm x 151 cm1920 x 1080 (16/9)4,20 m1,4 mm
308 cm (121″)270 cm x 151 cm3840 x 2160 (16/9)2,11 m0,7 mm
ECRAN 280 CM DE BASE ECRAN SCOPE 21/9   
305 cm (120″)280 cm x 119 cm1920 x 817 (21/9)4,20 m1,4 mm
242 cm (95″)211 cm x 119 cm1920 x 1080 (16/9)3,30 m1,09 mm
305 cm (120″)280 cm x 119 cm3840 x 1634 (21/9)2,21 m0,73 mm
242 cm (95″)211 cm x 119 cm3840 x 2160 (16/9)1,66 m0,55mm
SAMSUNG THE WALL ULTRA-HD 4K ECRAN 16/9  
190 cm (75″)165 cm x 93 cm3840 x 2160 (16/9)1,30 m0.43 mm
213 cm (84″)185 cm x 104 cm3840 x 2160 (ULTRA-HD 4K)1,45 m0.48 mm
370 cm (146″)318 cm x 179 cm3840 x 2160 (16/9)2,50 m0,828 mm
342 cm (135″)318 cm x 135 cm3840 x 1634 (21/9)2,50 m0,828 mm
556 cm (219″)484 cm x 272 cm3840 x 2160 (16/9)2,50 m1,26 mm
Samsung The Wall


ECRAN MICROLED SAMSUNG 146 POUCES 16/9 ULTRA-HD 4K
LE PLUS GRAND ECRAN MICROLED DU MONDE !

ECRAN PLASMA PANASONIC TH-103PF12EK


ECRAN PLASMA PANASONIC 103 POUCES 16/9 FULL-HD 2K (59 000 EUROS)
LE PLUS GRAND ECRAN PLASMA DU MONDE !

Distance de recul pour visionner un écran LCD FULL-HD 21/9 EME
avec une source FULL-HD


TELEVISEUR LCD LG ULTRA-HD 5K INCURVEE 105 POUCES
21/9EME CINEMASCOPE (5120 x 2160 PIXELS) (LG 105UB9)

Diagonale de l’écran
en cm (en pouces)
Dimension image visible en 16/9
(largeur en cm x hauteur en cm)
Nombre de pixels
(Largeur x Hauteur)
Distance de recul optimale Taille moyenne
du pixel
127 cm (50″) 117 cm x 50 cm 2560 x 1080 (HD) 1,38 m 0.45 mm
127 cm (50″) 117 cm x 50 cm 1344 x 576
(SD)
2,64 m 0.87 mm
147 cm (58″) 135 cm x 58 cm 2560 x 1080 (HD) 1,60 m 0.53 mm
147 cm (58″) 135 cm x 58 cm 1344 x 576
(SD)
3,04 m 1.00 mm
267 cm (105″)245 cm x 105 cm1344 x 576
(SD)
5,51 m1.82 mm
267 cm (105″)245 cm x 105 cm2560 x 1080 (HD)2,97 m0.97 mm
267 cm (105″)245 cm x 105 cm5120 x 2160 (ULTRA-HD 5K)1,45 m0.48 mm


TELEVISEUR LCD PHILIPS 50 POUCES 21/9
2560 x 1080 pixels FULL-HD 2,5K 3D PASSIVE (1400 EUROS)
L’ECRAN CINEMASCOPE PAR PHILIPS !

LES DIFFERENTS FORMATS DE DIFFUSION DE L’IMAGE

FORMAT = Rapport largeur de l’image sur hauteur de l’image

1.33(ou 4/3) format d’image utilisé par la télévision
1.37format d’image cinéma
1.5(ou 3/2) format d’image utilisé en photo pellicule 24*36
1.66 format d’image cinéma 35 mm européen
1.77(ou 16/9) format d’image télévision
1.85 format d’image cinéma PANAVISION film 35 mm
2.35 format d’image cinéma CINEMASCOPE film 70 mm ou 35 mm anamorphosé (21/9)

DIAGONALE :

Avec un format d’écran de 4/3 : Diagonale de l’image = 5/3 x Hauteur

Avec un format d’écran de 16/9 : Diagonale^2 = 337/81 x Hauteur^2

Avec un format d’écran de 21/9 : Diagonale^2 = 58/9 x Hauteur^2

FORMULES :

1 POUCE = 2,54 CM

Diagonale^2= Hauteur^2 + Longueur^2

DIAGONALE RECOMMANDEE
POUR UNE DISTANCE DE VISIONNAGE
DE 4,40M

RecommandatonsRésolutionAngleDistance/DiagonaleDiagonale / Distance DiagonaleDiagonale
ITU FULL-HD 101,58 pixels / degré18,9°2,610,38167 cm 65,8″
Oeil(16,5/10) FULL-HD 100 pixels / degré19,2°2,580,39171 cm 67,5″
SMPTE FULL-HD 64 pixels / degré30°1,630,6264 cm 104″
Oeil (10/10) FULL-HD 60 pixels / degré32°1,5750,635279 cm 110″
ITU Ultra-HD 101,58 pixels / degré36,9°1,310,76334 cm 131″
Oeil (16,5/10) Ultra-HD 100 pixels / degré38,4°1,250,8352 cm 138″
THX 40°1,20,84370 cm 145″

Exemple SMPTE FULL-HD:
Diagonale d’écran = distance x 0,6
Distance optimale = diagonale d’écran x 1,63

Exemples du choix de la distance de recul suivant le diffuseur :

Distance optimale de recul pour un téléviseur Full-HD 2k 50 » (127 cm) (Oeil 10/10 Full-HD) :
1,575×1,27=2,00 m

Distance optimale de recul pour un téléviseur Ultra-HD 4k 50 » (127 cm) (ITU Ultra-HD) :
1,31×1,27=1,66 m

Distance optimale de recul pour un téléviseur Full-HD 2k 65 » (165 cm) (Oeil 10/10 Full-HD) :
1,575×1,65=2,598 m

Distance optimale de recul pour un téléviseur Ultra-HD 4k 65 » (165 cm) (ITU Ultra-HD) :
1,31×1,65=2.161 m

Distance optimale de recul pour un téléviseur Full-HD 2k 75 » (190 cm) (Oeil 10/10 Full-HD) :
1,575×1,90=2,99 m

Distance optimale de recul pour un téléviseur Ultra-HD 4k 75 » (190 cm) (ITU Ultra-HD) :
1,31×1,90=2,489 m

Distance optimale de recul pour un vidéoprojecteur 2k avec un écran 105 » (267 cm) (Oeil 10/10 Full-HD) : 1,575×2,67=4,205 m

Distance optimale de recul pour un vidéoprojecteur 4k avec un écran 105 » (267 cm) (ITU Ultra-HD) : 1,31×2,67=3,49 m

Distance optimale de recul pour un vidéoprojecteur 2k avec un écran 121 » (308 cm) (Oeil 10/10 Full-HD) : 1,575×3.08=4,851 m

Distance optimale de recul pour un vidéoprojecteur 4k avec un écran 121 » (308 cm) (ITU Ultra-HD) : 1,31×3.08=4,03 m

Distance de recul SMPTE Full-HD (angle de vision 30°) = 1,63125 x base de l’écran = 1,63125 x 2,70 = 4,40 m

Distance de recul THX (angle de vision 40°) = 1,63125 x base de l’écran = 1,4619 x 2,70 = 3,94 m

David Gouvenel
Janvier 2019

Related Images:

Guide to Projectors for Interactive Installations

Original Text by Blair Neal 2014

Video projectors are one of the most important tools for creators of interactive installations. The information for projectors is available on various websites, but this 2 part guide will focus on their use in production and interactive environments. Part 1 will focus on the projector as hardware(lenses, lumens, surfaces etc), and part 2 will go into more details on the software and calibration considerations. This will gather some of that disparate knowledge into the important bits you need to make informed decisions about creating a high quality experience.

They vary in scale from pocket-sized (or smaller) pico’s to refrigerator sized large-venue projectors. They vary in price from a couple hundred dollars, to a couple hundred thousand dollars. In the end, however, essentially all projectors can be described as little more than a bright light element,  imaging elements, and a lens. There is something technical about projectors that seems to mystify some people, but it is really important to remember that they are just a flashlight that shoots a square shaped image. In this article we will discuss:

  • A checklist for planning your installations
  • Overview of projector types
  • Different classes of projectors
  • How to calculate projector intrinsics/How to read and interpret a spec sheet
  • How to calculate proper brightness
  • Discussion of video signal quality and cable lengths
  • Maintenance, Miscellaneous caveats and tricks of the trade
  • Experimental tech and the future
  • References and Thanks

Projection Planning Checklist:

Here is a sample checklist that you can go through when planning to choose a projector for an interactive installation or large event. Each decision made here has it’s own list of caveats and considerations that can affect the final outcome. Some of these topics will be covered more in depth later on:

  • What is the surface or object you’ll be projecting on?
  • Standard screen? Front or rear projection?
  • Fabric or scrim?
  • What color is the surface?
  • What are you projecting on? Flat surface or complex geometry? Is it an unusual shape/curved/architectural/sculptural
  • What is the environment like?
  • Inside or outside? Daytime or nighttime?
  • How much ambient light is there? Is it a bright show room, or a dim purpose-lit space? Is there lighting design?
  • How will you mount or place the projector?
  • Will the venue allow you to drill into the ceiling?
  • How will you run cleanly run cables from your command station to the projectors? (More on cable lengths later)
  • Where are people (or other objects?) going to be in relation to the projectors?
  • Is there a potential for shadows?
  • What image size are you trying to achieve?

Visiting the installation space in person is optimal when starting to plan. A visit will get you the best sense of space, available electrical outlets, positioning options and the sense of ambient light. Pictures and CAD drawings of the space are next in line of importance of things you should obtain for the space, even if you visit it. After that, it’s up to you if you want to sketch out placement on paper, model their placement in a 3D rendering, or make a scale diorama.

onionskin_projection

Onion Skin by Olivier Ratsi [Antivj] – Re-composition of time and space using perspective #Overview of Projector Types There are several different kinds of imaging and illumination methods used in video projectors, and each type has their own list of pros and cons. Each technology uses a different combination of light sources, mirrors, filters and lenses. Below, I’ll briefly explain each type, and you can check out some links in my sources for further reading:

DLP

DLP

This is one of the most commonly used projector types, and they often provide the most bang for your buck. A big selling point on DLP technology is that it can display much darker blacks than LCD technology which is especially helpful for illusions like projection mapping. There are a few different styles of DLP, Single chip and 3-Chip. In single chip DLP,  a light source is passed through a rapidly spinning multi-segment color wheel of 3 or more dichroic glass sections (7 or more color segments is a more « desirable » spec than 3). That light then bounces off a matrix of electrically controlled microscopic mirrors that determine the brightness of each individual pixel. The beam then passes through filters and out through a lens. The timing between the color wheel and the movement of the mirrors determines the color of the output.

With DLP projectors, the most noticeable side effect of this imaging method is a RGB effect that appears when you quickly move your eyes side to side. You will also notice a subtle rainbow banding effect if you capture the projection through certain types of cameras, especially CMOS DSLR’s. You can minimize this effect by adjusting your camera’s shutter speed to be slower. This banding effect is minimized or non-existent on 3-chip DLP projectors that split the light path in a similar way to how LCD projectors work so it syncs colors without a color wheel. A 3-chip DLP is a little more expensive though, and you’ll mostly find it on cinema projectors and ones with more than 10k lumens.

LCD

DLP

There are a couple different LCD technologies for projection, but 3LCD is probably the most recommended in terms of image quality. With LCD projection, a light source is bounced through 3 dichroic filters that turn the white light into precise red/green/blue frequencies. Those differently colored beams of light then pass through liquid crystal arrays that turn on and off their pixels and block the different light patterns to form the image. Those LCD’s are then recombined with a prism that recombines the 3 colored segments into a single light beam/image that then passes through a lens. Whew. LCD projection doesn’t have the rainbow banding effect that DLP does and tends to be easier to film, but it doesn’t have the darkest blacks, so it doesn’t disappear as much when the screen is just displaying a black image.

LCD Projector Teardown Video: Youtube Link

LCoS

Liquid crystal on silicon is almost a hybrid of how DLP and LCD work, and can provide advantages over both. LCoS has a reflective portion, but is also modulated by liquid crystal. There is no color wheel in this setup, as it does the light splitting technique similar to LCD. The primary current issue with this technology is that the contrast ratio tends to be much lower than DLP or LCD, so your contrast range from true black to bright white is reduced.

Hybrid

There aren’t many of these yet, but a couple brands have come out with hybrid light source projectors that boast extremely long lamp life (20,000 hours compared to the normal 2-3000 hours of a traditional lamp). These still use some of the traditional imaging sources as above, like DLP and LCD, but they replace their lamp bulb with a different solid state source like LED, Laser, etc etc.

Laser Diode

This is another fairly new player that isn’t wide spread yet. I’ve seen it in a new Sony projector and the yet-to-be released RedRay 4K. You can also find this as a light source in some of the smaller Pico projectors like Microvision’s. Primary advantage of a light source like this is that you don’t have to worry about heat dissipation as much as you would with a Xenon bulb.

CRT

CRT is almost nonexistent in this day and age, but hey, maybe you want to have a vintage party with a laser disc player or something. CRT projection was used a lot in some of those large 90’s era rear projection big screen TV’s. They feature 3 CRT guns in red, green and blue that fire electrons onto a phosphor surface, similar to a standard CRT. Then they are passed through a lens, and onto a projection surface (typically rear projection). The guns are very sensitive about their positioning and typically require re-calibration after moving them around. They are now mostly an interesting thing to scavenge for parts.

Different classes of projectors

Your project may be a small interactive tabletop game with a single pico projector in a dark room or a 200ft x 100ft projection bonanza with a dozen large-venue projectors. It’s very helpful to know and understand the capabilities of the ranges of the pico, the portable, the installation, and the large venue projectors.

Pico and Pocket projectors

Price range: $100-500 Brightness range: 10 lumens to 500 lumens Resolution range: 640×480 to 1280×800 Example

pocketprojector

These tend to be used in very specialized situations as they tend to have a limited range on the brightness they can provide (usually less than a couple hundred lumens, if that). Don’t expect to have a suitable image that is larger than a couple feet in width, even in total darkness. Pico projectors use different light sources like LED and lasers. Some even contain batteries for battery powered operation (or can be hacked to be battery powered). These tiny things also tend to have reduced resolution and you will more commonly find ones that are more likely in the 854×480 range than the 1080p range. Also, since their primary purpose is for enlarging powerpoints and small movie screens, you can usually be limited by specs on color reproduction and contrast ratio. One of the neatest qualities about a select few laser pico projectors is the fact that they have an infinite depth of field and require no focusing, so you can project on very close up things clearly. Their price is usually comparable to lower end office projectors in the 300-500 dollar range.

Portable projectors

Price Range: $400 to $2,000 Brightness Range: 500 lumens to 3000 lumens Resolution Range: 1024×768 to 1080p Example

portable_image

This class is mostly for the cheaper portable projectors that you might find in a small office or classroom. They often have a single lamp, are lighter, have less brightness options, and a lot less configuration options on their internal software. These ones can get you through certain installations in a pinch, but they aren’t necessarily designed to be as easy to support in an installation setting as the next class up. Some projectors just don’t handle 24/7 operation very well, so keep this in mind. You’ll be somewhat limited on your range of options for throw ratios and image sizes because of the limited brightness ranges at this price point. Some of them have very limited zoom adjustments, and no lens shift. You’re more likely to find cheap ultra-short throw (<0.7) projectors in this range, but their brightness leaves something to be desired any more than 5-8ft away from the surface.

And unless it’s dark DARK night time and your screen is a reasonable size, don’t even think about using these outside.

projector shot

Installation and Home Theater projectors

Price Range: $2000 – $10,000 Brightness range: 3000-10000 lumens Resolution range: 1024×768 to 1080p Example

installation_projector

It’s hard to cover this class concisely as there are a wide range of brands, lenses, and imaging elements. These will be the go-to for 90% of projects. They will cover you in most indoor installations if you’re trying to cover a reasonable amount of space (ambient light and windows permitting). These ones tend to be heavier and larger (15lbs+) but offer more configuration options than the portable class (like advanced geometry correction, control over LAN). They are also designed for 24/7 operation so they are more acceptable to use for long term installations. Some models also support multiple lamps so that in case one burns out, it can switch to another one. Maintenance and support is generally easier with these as well, but at an obvious jump in price.

These projectors also start to bring in multiple lens options for short throw 0.4 to long throw 12.0 ratio with the same body. They also offer more options for lens zoom and lens shift which are super handy.

If you’re trying to get more than a 20ft wide image or are dealing with stage lighting, see my section below about properly calculating brightness and size before you drop your coins on a specific one.

You’re also much more likely to buy one of these projectors for a short run than rent one. If you are running and installation for a week or more, it quickly becomes more cost effective to just purchase one of these classes of projectors (or the portables) because you would be paying the same amount in a week or so anyway.

Large venue projectors

Price Range: $5000 – $Infinity Brightness Range: 5000 lumens to 42,000 lumens (I’ve heard 100k lumens before, but can’t find a reference) Resolution Range: 1024×768 to 4K Example

largevenueimage

These ones can range from a form factor of about 2ft x 2ft x 8in all the way up to the size of a kitchen refrigerator. As brightness increases, so does the price and the space/ventilation/power requirements (and weight!). Another consideration is that at a certain point (around 15k lumens), 120V/15A mains just won’t cut it for a single projector, and you’ll need an electrician or special setup (240V/3 phase in US) to actually power the beast.

The high powered bulbs in these ones are also much more of a safety issue. When choosing a 20k versus a 30k rental for an event, I was told a professional projectionist would need to install the bulb in the 30k as it was unsafe to transport the projector with the expensive and fragile bulb inside. I was also told a fire marshall may need to be present to approve the safe operation of the projector as it presented a more significant fire hazard. The power of the bulbs also significantly shortens their lifespan down to about 1000 hours of operation compared to the smaller ones. The aging of these bulbs also has a much more noticeable effect on the image. Older bulbs will look much dimmer and more off color than brand new bulbs – something to keep in mind if you’re working with multiple high power projectors is to keep an eye on bulb life.

Placement and mounting of these projectors is another important consideration. Some of the larger ones weigh 300+ lbs and will require trussing and investigation about whether the ceiling or structure can actually support them. For some events you may end up constructing a scaffold tower with the huge projector on top, and with your power supplies, media servers and workspaces underneath.

Like installation projectors, large venue projectors often offer multiple lens options for the same projector. Most offer throw ratios from 0.8 to about 7.0 or 12.0. These super zoomed ratios are helpful if you have a really tall building to projection map from the ground, or a screen that is over 100ft away and you’re trying to conserve your precious photons.

You’re also more likely to have to rent one of these projectors rather than purchase, so be prepared to source a rental house (who often require pricey production insurance, a solo artist will find it difficult to rent one!). Also owning one of these would be a pain because they are heavy, awkward, expensive to maintain, and you would need to rent them out yourself in order to break even. Prices vary on length of rental and type of equipment. From personal experience, I can tell you that a 20k lumen projector will run you roughly $1000-1500/day (including your lens choice), and 6k-10k lumens run around $700-1000 a day depending on lenses and HD requirements.

I wouldn’t suggest planning to rent one of the larger ones for a long term installation unless you have some serious budget. The prices to purchase these shoot up sharply after about 10k lumens. Most 20k lumens and above will run you $40,000 to $80,000 and beyond.

How to calculate projector intrinsics/read a spec sheet

Being able to interpret a projector spec sheet is an invaluable skill to have when planning your project. You’ll have to separate the parts that are important, from the values that aren’t standardized or are there for marketing fluff-

Image

Resolution: This is the actual maximum resolution the projector is capable of displaying. You can send it higher resolutions than this, but the physical number of pixels will remain the same. If it’s native resolution is 1280×800 and you send it 1080p, there is just going to be down sampling to match native resolution. If you see the spec « Supported Resolutions »  – Warning! This spec is nearly useless and incredibly misleading. Only pay attention to the native resolution if you want the physical pixel count. Supported resolutions just means the resolutions that the projector is capable of accepting and then down sampling or up sampling to match its native resolution. There are 1024×768 native projectors that « support » 1080p but that doesn’t mean all those pixels are actually coming out of the lens.

Lumens: This spec is somewhat standardized with ANSI units, but different manufacturers can waver a bit. A difference of a couple hundred lumens between projectors isn’t much to consider if you need something slightly brighter, it’s easier to think in 1000 lumen increments generally. Also, as a guidance, you’ll want at minimum around 20 lumens per square foot of image.

Contrast Ratio: This is another misleading/non-standardized unit. Ideally this will tell you the dynamic range or number of black pixels you would need to « stack » on top of eachother to make a white pixel. 1:300 contrast ratio is poorer than 1:10,000 but companies use different ways to quantify their contrast, so it can be very hard to gauge what the reality is until you get one. Some projectors also have dynamic contrast which means that they automatically adjust their lens to provide darker blacks depending on the image that is coming through. Bit depth is also loosely related to contrast, but it is more of a limitation within video technology than the projector technology. Bit depth (8bit,10bit etc) would be the number of possible « steps » between a black and white pixel.

3D: Occasional marketing fluff spec – read specs carefully if you really need 3D. Many projectors are « 3D capable » if they have HDMI. Some of them operate at 120hz and work with active shutter glasses, but some setups you will need 2 projectors and some special polarizing filters and silver screens to actually make it work as well as a movie theater. Essentially, plan on extra equipment if you’re looking to do 3D, or read very carefully.

Fluidic

Fluidic – Sculpture in Motion by WHITEvoid

Geometry

Throw ratio: This is probably the second most important specification behind lumens. This value gives you the ratio of the width of the projected image to the distance from the surface. For example, a throw ratio of 1:1 means that for every 1ft away from the wall, you will get 1ft of image width (and your height is determined by the aspect ratio). Sometimes this is given as some random unit like « 66 » @2m » which is usually diagonal size of the image at a certain distance. Lens zoom is also a related property because it allows you a small « variable » lens shift.

Lens Shift: Lens shift is generally only available on higher end projectors. Most projectors have a slight lens offset that allows them to be below or above their screen and still have a square image (different than tilting!). Lens shift allows you to correct for this offset if necessary – just tilting the projector would result in more keystoning. Some have manual or motorized lens shift. This also lets you worry less about exact placement of your projector because you will be able to shift the beam around – just watch for vignetting on the edges!

Physical

Inputs: Make a note of these to make sure you have options with VGA or HDMI or whichever. We will discuss analog versus digital connections further down.

Watts/Power Consumption: This is important to have on hand if you’re wondering if you might blow a circuit by running multiple projectors. See below on how to calculate it.

Size/Weight/Noise Level: Always good to know your dimensions if you need to fabricate a special box or fit it into a tight area. Weight is also very good to know for when you’re choosing mounts or calculating whether the ceiling can hold the thing. Also good to note how loud a projector is going to be if you’re doing a quiet/sound based installation – I’ve heard some loud ones before

Quick note about power consumption – it’s always good to know off hand how much power your event or installation setup requires. In the US most electrical outlets are 120V/15A, EU is 240V/16A generally. Most spec sheets will give your projector power consumption in watts (sometimes as: eco power mode, normal, and lamp-on). Once you have the number of watts and you know the voltage of the electrical outlets, you can calculate how many amps you need so that you don’t trip the circuit you’re running off of. The equation is:

Watts/Volts = Amps 300W(projector power consumption)/120V(supply voltage from outlet) = 2.5Amps

You could potentially run 5 (12.5A) of these theoretical 300W projectors on a single 15A circuit. Always leave yourself some headroom with power demands – know in advance if you need more dedicated circuits. Some projectors also may need a larger pull of power when they first spark the lamp, so keep that in mind when powering up.

Working with Throw Ratio

ThrowRatio

Now let’s talk about throw ratio and how you can make it work for you. Feel free to use the many online projector calculators and apps – but it’s good practice to run the numbers yourself. Sometimes the online calculators don’t have the applicable options or sort of obfuscated results expressed in odd units or diagonal size (help me, Pythagoras). Using your throw ratio only, you can easily calculate the image width and height for a given distance.

Lightleaks

Light Leaks by Kyle McDonald and Jonas Jongejan – Filling a room with projected light

Throw ratio = distance from surface/width of image  0.5=2/x or at 2ft from a wall with a 0.5 throw ratio makes an image that is 4ft wide

From this value we can also get the height of the image if we know the aspect ratio (eg 16:9 or 4:3) of what we are planning to project (or the aspect ratio of the projector’s native resolution)

Image height = (1/aspect ratio) * Image Width From the above example, if we have 0.5 throw 2ft away with a 16:9 aspect ratio, what is our height? Height = 1/(16/9) * 4 =  2.25ft

Now that we know the width and height of our image, we can now easily calculate the answer to the question covered in the next section: « Is this going to be bright enough? » You can also use this value to calculate the angle of the projection frustum on the horizontal and vertical if you’re curious about how close people can get to the projection surface before they start causing shadows. You’ll need to know the projector offset to get really exact about this though – most projectors don’t come 100% straight out of the lens without lens shift.

Please note to always calculate things to be bigger than you need them to be by a few percentage points. Manufacturers numbers can be slightly off, or your placement may need to shift slightly. Giving yourself an extra +/- 5% of image could be really helpful. Be careful not to overshoot too much and throw away resolution and brightness though – try to hit that sweet spot.

How to calculate projected brightness:

There are a few different ways to measure brightness of a projected image. One way to think of projected light is as a paint bucket full of a finite amount of photons. You’re always going to have the same amount of light-paint, but the more you spread it, the « thinner » the coat gets, subsequently dropping brightness. Our primary concern is our lumens per square foot ratio, as this is the value that really changes the final output. This is just calculated as:

Total Lumens/Area of projection 2000Lumens/40 sq feet of projection surface = 50lumens/square foot

Ideally (and anecdotally) you want to stay above a minimum value of around 20lumens/square foot (or around 215 lumens/sq. meter). Once you dip below that value, you run the risk of your brightness and contrast being so weak that your image is washed out or unacceptably dim in less than ideal conditions.

There are many factors that can alter the eye’s perception this calculated value including:

  • Screen type/Screen gain – reflectivity of the screen
  • Surface type – May be the side of a building, or a block of wood, or a regular white vinyl screen.
  • Ambient light – dim gallery, bright show room, etc

Your type of surface can also affect your total brightness and contrast. Walls, screens, building exteriors, scrims, front or rear are all decisions that carry their own potential issues. Avoid really dark surfaces at all costs, as they absorb much of your photons and don’t reflect as many. However, in some situations gray screens are preferable over white screens because the gray can absorb more of the ambient light and improve contrast.

Rear projection can also cost you some brightness depending on the materials you’re projecting through. Rear projection has the side effect of giving you a fat hotspot right in the middle of your screen where the projector bulb is. To avoid the hotspot effect you need a rear projection material that can really diffuse the light at the expense of photons and contrast. A low gain screen will diffuse the light more and make it more even with rear projection but it will decrease the overall contrast because it also picks up more of the ambient light. A low gain screen is as efficient as a high gain screen, but it spreads the photons out to more viewing angles, so not as many are concentrated coming straight out at the average viewer. A high gain rear projection screen will seem a little more « transparent » which will improve contrast, but you will get a larger hotspot in the center. There are also specialized screens like 3M’s Vikuiti film that uses a light absorbing layer and glass beads to provide an ideal experience of limited hotspot and while also absorbing ambient light for really deep blacks.

You can use a light meter to determine the ambient light in your space so you know what your reference point is. Once you know this value, you have an idea of the brightness you’ll need for your projection to compete properly. You would need a light meter that measures in footlamberts to give you an easy to work with value for the ambient light in your space.  Personally, I have heard to try and make your brightness about 8 times brighter than expected room brightness so you can get acceptable contrast from the baseline of light in the room, but this is highly variable depending on your environment and intended effect. For example, an ambient light value of 5fl in a space would recommend a projected value of around 40fl to compete properly. You can obviously get away with less (or more), but keep these values in your pocket if they become necessary.

Stacking two matching projectors on top of each other does NOT mean the image will perceptually appear to be twice as bright. For example if you stack two 4000 lumen projectors, there are still 8000 lumens bouncing back at you, but your eye’s perception of brightness is not linear, so it will not be seen as two times as bright – just brighter. You can also use the stacked projection to cover twice as much area with the same perceived brightness as using just one with half the square footage. Stacking also brings up the issue of brightening the black level with 2 stacked projectors, which in turn will change the perceived contrast between black and white and image quality. For optimal perception for your eyes, you want the projected image to have as much contrast from the surroundings as possible…there is a reason we watch movies in dark theaters.

To stack projectors you will ideally want ones in the installation or large venue class with motorized lens shift or ones that offer perspective distortion in their hardware – otherwise aligning the images of 2 projectors to be pixel perfect can be a nearly impossible feat. Access to lens shift is preferable, followed by the projector doing the actual distortion. You can do homography distortion in software to align the two, but then you’ll need to essentially double your video output to output different streams. #Video signal quality and cable lengths Your video signal path is another very important consideration when planning. Analog and digital signals have their strengths and weaknesses. You will need to ensure your computer is compatible or you have the right adapters – especially if you’re working with an existing projector system in a space (S-Video anyone?)

DVI/HDMI

DVI and HDMI are the most common digital video cables right now. DVI can support a wide range of resolutions, and can handle the highest ranges with a dual link (DVI-D) cable. Single Link DVI is missing some of the center pins and has a lower bandwidth, it maxes out at 1920×1200 @60hz which is about 3.96gbit/s of data. Dual Link DVI cables are only technically limited by the copper bandwidth limits, DVI source limits and sync limits. Dual Link cables occasionally list their bandwidth resolution limits of around 9.9gBits/second which you can use to check your intended use and how close you may be to hitting the ceiling.

Resolution Width * Resolution Height = Total Number of Pixels Total Number of Pixels * Refresh Rate = Total Number of Pixels per Second Total Number of Pixels per second * Color resolution bits = Total Bits Per Second

2560*1440 = 3,686,400 pixels 3,686,400 * 60hz = 221,184,000 pixels per second 221,184,000 * 24 (Bits of color) = 5,308,416,000 bits per second = 5.3gbit/s

I tend to trust DVI cables up to about 35ft, although the spec will get you to about 50ft. HDMI cables are more reliable at longer distances and have a larger consumer marker so it may be easier to find a reliable long cable. Symptoms of a digital cable that is too long or poor quality (or just not plugged in all the way!) will be something like:

  • Unpredictable sync behavior
  • Strange « noise » with the pixels, particularly in the blacks or on smooth gradients – this is a result of certain digital bits being flipped incorrectly because they weren’t transmitted correctly over the cable. You can see this in the image below

![DVI Artifact](images/HDMI_glitch.jpg)

They sell longer HDMI and DVI, but unless it’s really thick or your have had time to test it with your desired equipment, I would highly recommend an extender for distances over 100ft. Extenders come in different flavors and budget ranges, but it tends to be a case of « You get what you paid for » so don’t expect a 20 dollar no-name brand extender to give you 100% reliability. There are signal boosting couplers, extensions over Cat5/Cat6, and extension over fiber optic. Cat5/Cat6 extenders can be used with VGA/DVI/HDMI but some of them can be especially finicky with certain output or display devices, so try and test as realistically as possible beforehand. Fiber optic extenders are top of the line because of their clean signal quality and ability to extend over 1000ft on a single cable. Fiber is VERY delicate (roughly handling it or kinking the cable can shatter the glass inside) and needs special considerations when running it. Fiber is also one of the more expensive extension options, so be prepared to rent your cable and extenders.

A final note is to pay attention to how your extender handles passing an EDID. An EDID is basically a packet of info that a video source and destination share that gives info about resolutions and timings. Without a proper EDID handshake, you’ll be scratching your head « trying to figure out why this still isn’t fucking working! » Some extenders send EDID over a separate Cat5 cable, so keep this in mind when constructing wiring diagrams. There are EDID Emulators and DVI Doctors that go in between a source and display. These devices can do things like « store » the EDID of a display and keep it in case you are going between your display and another device that disrupts the EDID like a switcher. Other DVI Doctors also work to clean up the DVI signal to make it easier to extend the signal, sort of like an amplifier.

SDI/HD-SDI

HD-SDI Cables are a great cable for sending video long distances. You’ll commonly see them being used to send HD video from cameras into switcher and recording setups. They use a fairly common BNC barrel connector. You will often need a converter box to send your HDMI/DVI signal over HD-SDI since most computers don’t offer that as an output option without something like a Black Magic card. ## VGA ![VGA_noise](images/vga_noise.jpg)

VGA is the most common analog cable that is still kicking around. It is still able to push 1080p and above at certain distances, but it will probably die out over the next decade as we transition to 4K. VGA cables are good in a pinch with lower resolutions at longer distances without boosters, but I wouldn’t recommend them in professional use. The higher the resolution you’re trying to shove down that copper pipe, the less potential success you’ll have at getting your computer or projector to recognize the device at the other end because the same cable has to manage more bandwidth and needs a higher quality output device to generate the higher resolution clock timing for the analog signal. VGA also has the issue of analog distortion or a certain degree of « fuzziness » and color shifting because the colors are sent at different high speed clock frequencies, and this gets exacerbated on longer cables or on lower quality output devices. The inconsistency of analog can also mean you may get slight pixel offsets that you wouldn’t get with a digital cable.

Maintenance, miscellaneous caveats and tricks of the trade

Maintenance tips:

NEVER (EVER!) UNPLUG A PROJECTOR with its lamp on. It can potentially destroy your expensive bulb! Projectors run their fans for a minute or two to cool the bulb in preparation for the next lamp on. If you unplug a hot projector, plug it back in and shock it with the electrical charge needed to spark it on, you risk damaging the delicate filament and either blowing your bulb out or severely reducing the lifespan. If you happen to unplug a projector while it is on, let it cool for 10-30minutes before turning it back on. Don’t try to turn it back on hoping you can get the fan going or something.

Ventilation is important!

Projectors need to suck in new cool air, blow it over the bulb to absorb its heat, and then push it out another side. Without air flow, the bulbs temperature can rise to unsafe levels. Luckily, most projectors have detectors for this and will automatically shut off when their bulb temperature reaches a certain threshold. Still, you probably want to avoid having your projector auto-shutoff during an event or long running installation. Most manuals will also advise you not to run your projectors sideways in « portrait » mode because it will change the factory designed airflow and shorten bulb life – I haven’t personally experienced a significant issue with running them portrait, but it is trickier to manage their air flow in this position. Some projectors also have a specific filament placement that can impact whether it is safe to run them in unusual configurations because the filament may not be centered within the bulb. ## Projector placement considerations ![ProjectorWarping](images/ProjectorOffsetDiagrams.png)

In the event that you can’t get enough distance to get the desired image size, you have a few options. You can get multiple projectors and edge blend them (complex setup depending on your environment). A lot of consumer ultra short throws that are closer than 0.8 throw have setups so that they bounce the beam off a mirror and overtop of the projector to get every inch of possible distance. A mirror is a good way to extend the distance of your normal projector as well, with an important caveat: you need what is called a first surface mirror, or front surface mirror. A first surface mirror has the reflective coating on the top layer rather than underneath the glass. A normal mirror with coating on the backside will have a potential to give you a double image or color distortions because of the beams bouncing from the glass and the reflective surface.

Ultra short throws and mirror solutions have a noteable side effect to plan for: projection offset. I have experienced this a few times first hand until I figured out my mistake. When using these solutions, the projector will need to be either sigificantly above or below the center point of the desired screen. Sometimes they need to be almost 3-5 ft below the bottom or top of the screen itself. Trying to shoot these offset solutions straight out to the center will result in extreme warping and a reduction in image size (primarily height).

maintenance

Misc.

A wide angle/short throw lens will have the effect of giving you a lower depth of field which would be relevant if you are doing some kind of projection mapping that would have a lot of depth to it. The focus and brightness fall off much more quickly than with a longer throw lens, so mapping with these can be a challenge. 0.4 Throw to 0.8 throw is usually a lens solution, but 0.4 and less usually involves a curved mirror which limits your ability to focus on much more than a plane.

Experimental Tech and the Future

The following are some links to some equipment that would be fairly unusual to see in most major productions at the moment.

A big dream for a lot of us would be to have a projector with an embedded infrared camera that looks through the exact same lens as the projector in a 1:1 relationship so that there is easy alignment between camera and interactive content.

Texas Instruments DLP Dev kit for embedded projectors in other projects – http://www.digikey.com/product-highlights/us/en/texas-instruments-dlp-technologies/688

TI’s Pico Projector with Ultraviolet light source – http://www.ti.com/devnet/docs/catalog/thirdpartydevtoolfolder.tsp?actionPerformed=productFolder&amp;productId=16180

Projection Design’s 1080p Infrared Projector – http://www.projectiondesign.com/products/fs33-ir-series

Sony’s 4K Projector – http://www.cnet.com/products/sony-4k-ultra-short-throw-projector/

Projection Design’s Remote Light Source – Allows for your light source to be a few meters away from your for space and noise concerns – only at around 2000 lumens right now: http://www.projectiondesign.com/corporate/press/projectiondesign-fr12-remote-light-source-projector-in-control-at-ons

Also, having a look at the DIY projector scene can give you some really interesting ideas. You can make an almost passable projector with an LCD screen and a fresnel lens surprisingly enough. http://www.instructables.com/id/homemade-projector-cornflake-box/step4/attach-magnified-glass/ && https://www.youtube.com/watch?v=n_3RDuOV3qU


Thanks

..to Kyle McDonald, Chris Jordan, Zach Leiberman for providing input and reviewing the article. Huge thanks also to Elliot Woods who gave me a really helpful review with extra tips and probably the most hilarious point by point commentary on the article.

Other resources to check out:

Wikipedia for DLP: http://en.wikipedia.org/wiki/Digital_Light_Processing

On the maximum length of VGA: http://www.wirelessforums.org/alt-comp-hardware/max-resolution-vga-connector-22437.html

Da-Lite’s (somewhat dated) articles on projection: http://www.da-lite.com/education/angles_of_view.php

Using light meter to determine brightness: http://www.avsforum.com/t/755705/using-the-ca813-light-meter-to-measure-your-front-projector

Digital projector myth: http://www.kenrockwell.com/tech/digital-projector-myth.htm

3 types of projectors explained: http://forums.afterdawn.com/thread_view.cfm/74117

http://www.engadget.com/2012/04/16/redray-4k-cinema-laser-hands-on/

Remote light source: http://www.projectiondesign.com/products/fr12-series

Top 10 Pico: http://www.projectorcentral.com/popular-pico-projectors.htm

Reading about LCoS: http://www.projectorcentral.com/lcos.htm

Discussion about stacking projectors: http://forums.prosoundweb.com/index.php?topic=96088.0

http://www.electricstuff.co.uk/picoproj.html

Should you use white or gray screens? – http://www.projectorcentral.com/white_gray_projection_screens.htm

What is Screen Gain? –http://www.projectorcentral.com/projector_screens_gain.htm

Brightness – http://www.projectorcentral.com/home_theater_projector_buyers_guide.htm?page=Brightness

debugview

LINE SEGMENTS SPACE by Kimchi and Chips, 2013 / Projection, Nylon string, Code.

Related Images:

LED by garageCube

Mon nouveau Jouet !!

À propos du projet

A plug-and-play LED Kit designed for stage design, visual art, and live performance. User-friendly and adaptable for structure assembling using aluminum profile. Simple and ergonomic.

 

LED by garageCube can be plugged together in any order and are auto addressable. A single cable carries both power and data, reducing connections to a minimum. Our LEDs are a perfect complement to madMapper, but are also compatible with third party applications and lighting desk consoles.

 

 

With madMapper, the most advanced video and LED mapping tool, you can easily set up from simple to large scale installations. You can use all kinds of content, such as video files, live feed, and generative images, to control your LED by garageCube.

 

Use your favorite MIDI controller for perfect live control. You can use all kinds of content including video files, live camera feeds, and generative images to control your LED by garageCube.

 

 

LED by garageCube will be available in RGB or pure white, and in two different sizes: 50 cm and 1 meter. Light diffusers and transparent covers are included in the Kit.

 

The 50 cm bar fits in your hand luggage. No need to check them in when flying. Sixteen 50 cm bars are lighter than 4 kg!

 

 

Thanks to their aluminum design, LED by garageCube is lightweight and solid. Attach them to your brackets with simple M4 fixing screws.

 

The bracket system was designed for the LEDs to allow assembly in multiple positions and orientations. Two mounting brackets per LED strut are included in each kit.

 

 

Our system is also compatible with standard fastening elements available on the market either directly on the profile adapted for hex head screws or on our bracket mounting system.

 

The system has also been developed to realize complex structures combining 3D printing or other tailored fabrication techniques, making any of your DIY creations possible.

 

 

For manufacturing, we benefit from the experience of our Chinese partner, with whom we have been working for many years on the production of custom-made LEDs. Electronic parts are tested through several quality controls to ensure optimal quality.

 

  

 

 

 

 

Boris has been active in the audio visual field for over 10 years. With his Swiss company garageCube, he created the software modul8 dedicated to live video mixing. Then, in collaboration with 1024 architecture, they created madMapper a software solution dedicated to video and LEDs mapping. After designing some installations and making custom-made LEDs specific to his projects, he met Alexandre and the need arose to create a more versatile product, more adapted and accessible to the community of artists and audiovisual designers in which they evolve. After more than a year of research and testing on small and large scale installations, they decided to launch a Kickstarter campaign to make the product achievable and accessible to all.

 

Des questions sur ce projet ? Reportez-vous à la FAQ

Related Images:

Olga set kit

 

Olga set kit

 

Triangles to connect together in order to create video mapping areas

 

A kit as easy to assemble as to disassemble

The structures created with Olga can cover on average an area of 1m20 by 1m20. The assembly is easy and you will get a result in less than 30 min!

THE KITOlga is constituted of 30 equilateral triangles and 60 fixing strips. The kit contains 3 elements of 5 triangles, 5 elements of 2 triangles, and 5 elements of a single triangle

MountingThe kit can be quickly mounted and dismantled and as many times as you wish. The materials have been studied in order to guarantee resistance over time.

 

Olga is convertible according to your tastes

Olga is designed as a kit of modules reusable in multiple configurations. Assemble and reassemble Olga according to your project !

Are you lacking ideas? Find inspiration with ours User guide.

Olga
 

Olga enhances your mapping projects

The triangles have two projection surfaces, one matte and one glossy. Choose the best rendering for your installation.

Need to know more ?

Discover all the technical features of the Olga kit, and even more.

Technical specifications

 

Related Images:

HeavyM 1.6.2 News

HeavyM 1.6.2 News

Old versions

FOR THE BACKERS OF OUR KICKSTARTER, YOU HAVE TO GET AN UPGRADE TO GET THIS VERSION.

New Features :

  • Text in the players
  • Export output as video
  • CUE points for videos
  • Color opacity for each color
  • Color for special filling
  • New Random Color parameters
  • Toggle between user-defined and default center for each effect
  • Save/load for midi parameters
  • Color mask for players

Improvements :

  • Copy the effects from one group to another
  • Reset group effects
  • Shaders inputs
  • Colors saved directly in the color picker
  • Effects optimization
  • Structure effects for ellipses

New design:

  • Sequences
  • Modal windows
  • Color picker
  • Zoom module

FFmpeg integration

  • New format: .avi, .flv, …
  • New codec: hap, dxv, …
  • 4K

More Infos on : heavyM.net

Related Images:

HeavyM on Kickstarter !

HeavyM on Kickstarter !

HeavyM is an intuitive projection mapping software, it is currently running in beta version. It allows the creation and projection of visual animations with great facility, in order to be projected on real surfaces with a projector. You can also use your own video contents, the software will adjust them automatically to your settings.

Before the beginnings of HeavyM, our dream was to do projection mapping, sadly we did not have the skills in infographics and motion design. Nevertheless, we were experienced in programming, that is how we came with the concept of a software that would generate animations adaptable on any volume configuration for us.

After developing a first Beta version, with which we had lots of fun, we decided to share it with you, for free. A large amount of you had downloaded this first version, and we did not expect such enthusiasm. Today, your energy is pushing us towards concentrating on HeavyM’s development, in order to create a tool corresponding to your needs. This campaign is crucial for HeavyM’s growth, now we need your support so we can go even further and develop the most awaited features. Let us all join today so we can create the greatest public community revolving around projection mapping.

https://www.kickstarter.com/projects/1025614375/heavym-bring-projection-to-another-level

With Thunderclap, you allow to publish a message on Facebook or Twitter the June 17th, announcing the campaign’s halfway point.

Thank you for relaying the information to the greatest number and make the HeavyM’s community even bigger !

It’s really quick & simple :

– Press « Support with »

– « Add my support »

– « Allow publishing »

– And that is good, everything is 100% secure

Thank you again 🙂

Related Images:

Audio Visualizer with Resolume Avenue 4 (TIPS No.01 & 02)

Tips1

Visualize Line Scape with audio reacting.

 

First, please do adjust the playback BPM speed by fitting the value of BPM when sound data inport.

1.FFGL Sources in Sources tab

 

2. Adjust Line Scape parameters

Tips2

Stingy Sphere animation made from Lines animation with audio reacting

 

1.Select Lines in Sources tab

2.Adjustment Lines Parameters

 

3.Add Shift Glitch effect in Effects tab

4.Add Stingy Sphere effect from Effects tab

 

3.Add Delay RGB effect in Effects tab for final seasoning.

Related Images: